The joysticks of Nintendo Switch game consoles are easy to break. I believe that if you use them for more than a year, you will definitely have to replace the joysticks. But to be honest, the hard shell bags on the market are not very hard. If you press anything even slightly, the joysticks will be crushed. , and the size is not very small. I have looked at a lot of them, but none of them are satisfactory, so why not design one yourself?

This pressure-resistant hard protective case specially designed for Switch OLED has the ultimate size and is smaller than all bags on the market. Because there is no zipper, and the game console is placed at an angle, it is lower in height and the hinges and buckles are smaller. The size is compressed to the minimum and the strength is sufficient. The whole is compression-resistant and anti-collision. To prevent wear and tear, it is best to stick some flannel inside.

In addition, there are 5 slots for game cards, and the card slots are flexible, so you don’t have to worry about them falling.

The size fits perfectly with the switch oled, and the gap is about 2mm, which is enough for another layer of protective cloth or sticker.

There are two holes in the front for easy threading of a rope as handles.

The hinge uses a 1.75mm consumable material as the rotating shaft. After testing, the durability is sufficient. If you are not worried, you can find a 1.5-1.8mm iron wire.

The overall size is 251mm x 112mm x 32mm, which is only slightly larger than the size of the switch (102mm x 242mm x 13.9mm, 13.9 here does not include the bump).

As long as your 3D printer can print an area of more than 251cm, it can be printed. All are 3D printed components without supports.

The free version is the model seen in the picture, which is the v1 version. The model is now on sale for one week and will be taken off the shelves a week later. If you buy it now, you will enjoy 1 version iteration (i.e. v2), which will have many improvements.

https://www.youtube.com/watch?v=paKkZHJ17_8

任天堂的Switch 游戏机摇杆很容易坏，相信用超过一年绝对有换过摇杆的，但是市面上的硬壳包说实话，真的不是很硬，稍微压点东西也会压到摇杆，而且体积并不是很小，综合看了很多，没有一个满意的，所以为什么不自己设计一个呢？

这个专门针对 Switch OLED 设计的携抗压硬防护壳，极限尺寸，比市面上所有的包包都要小，因为没有拉链，同时游戏机是倾斜放置，所以高度更低一些，铰链和卡扣也尺寸压缩到最低，强度也足够。整体抗压防撞，为防止磨损，最好在内部贴一些绒布。

另外还留有5个游戏卡位置，有弹性卡位，不用担心掉落。

尺寸与switch oled 完全贴合，缝隙大约2mm，足够再贴一层保护布或者贴纸。

前面留有两个穿孔，可以方便穿一根绳子作为提手。

铰链使用一根1.75mm的耗材作为转轴，测试之后，耐用度也是足够的，不放心可以找一根1.5-1.8mm的铁丝。

整体尺寸为 251mm x 112mm x 32mm 只比switch 的尺寸（102mm x242mm x 13.9mm，这里的13.9不包括凸起）大一点而已。

只要你的3D打印机可以打印面积超过251cm即可打印，全部为3D打印元件，无支撑。

免费版为图片所见模型，即v1版本。现在模型出售一周，一周之后下架，此刻购买，将享受1个版本迭代（即v2），将有很多改进。