Small test piece to test support settings.

The part is a little bit bigger than the original desgin 40 x 40 x 15 and printed in around 2 hours at 0.16 mm layer height.

;========================================================================== ; Documentation ;========================================================================== ; Profile ( Version Cura 4.3.0 ) : A13 (0.16) ; Quality : Super Quality ; Material : PLA ; Diameter : 1.75 mm ; Nozzle Diameter : 0.4 mm ;-------------------------------- Quality -------------------------------- ; Layer Height : 0.16 mm ; Initial Layer Height : 0.2 mm ; Line Width : 0.4 mm ; Initial Layer Line Width : 100 % ;--------------------------------- Shell --------------------------------- ; Wall Thickness : 1.2 mm ; Wall Line Count : 3 ; Outer Wall Wipe Distance : 0.0 mm ; Top Layers : 5 ; Bottom Layers : 5 ; Top/Bottom Pattern : lines ; Outer Before Inner Walls : [False] ; Compensate Wall Overlaps : [True] ; Fill Gaps Between Walls : nowhere ; Print Thin Walls : [False] ; Horizontal Expansion : 0 mm ; Z Seam Alignment : sharpest_corner ; Seam Corner Preference : z_seam_corner_weighted ; Enable Ironing : [False] ;-------------------------------- Infill -------------------------------- ; Infill Density : 10 % ; Infill Pattern : grid ; Infill Overlap Percentage : 10 % ; Gradual Infill Steps : 0 ;------------------------------- Material -------------------------------- ; Flow : 100 % ; Printing Temperature : 195°C ; Printing Temperature Initial Layer : 195°C ; Build Plate Temperature : 60°C ; Build Plate Temperature Initial Layer : 60°C ; Enable Retraction : [True] ; Retract at Layer Change : [False] ; Retraction Distance : 5 mm ; Retraction Speed : 50 mm/s ;--------------------------------- Speed --------------------------------- ; Print Speed : 50 mm/s ; Infill Speed : 60 mm/s ; Wall Speed : 25.0 mm/s ; Outer Wall Speed : 25 mm/s ; Inner Wall Speed : 50 mm/s ; Top/Bottom Speed : 25 mm/s ; Support Speed : 25 mm/s ; Initial Layer Speed : 15 mm/s ; Skirt/Brim Speed : 15 mm/s ; Enable Acceleration Control : [True] ; Print Acceleration : 500 mm/s2 ; Travel Acceleration : 500 mm/s2 ; Enable Jerk Control : [True] ; Print Jerk : 8 mm/s3 ;-------------------------------- Travel --------------------------------- ; Combing Mode : off ; Retract Before Outer Wall : [True] ; Avoid Printed Parts When Traveling : [True] ; Avoid Supports When Traveling : [True] ; Travel Avoid Distance : 0.625 mm ; Z Hop When Retracted : [False] ; Z Hop Height : 0.2 mm ;-------------------------------- Cooling -------------------------------- ; Enable Print Cooling : [True] ; Fan Speed : 100 % ; Initial Fan Speed : 0 % ; Regular Fan Speed at Layer : 4 ; Minimum Layer Time : 10 s ; Minimum Speed : 20 mm/s ; Lift Head : [False] ;-------------------------------- Support -------------------------------- ; Generate Support : [True] ; Support Placement : buildplate ; Support Overhang Angle : 45° ; Support Pattern : zigzag ; Connect Support ZigZags : [True] ; Support Density : 15 % ; Support Z Distance : 0.2 mm ; Support X/Y Distance : 0.8 mm ; Support Distance Priority : xy_overrides_z ; Enable Support Interface : [True] ; Enable Support Roof : [True] ; Support Interface Thickness : 1.28 mm ; Support Roof Thickness : 1.28 mm ; Support Interface Resolution : 0.2 mm ; Support Interface Density : 30 % ; Support Interface Pattern : grid ;------------------------- Build Plate Adhesion -------------------------- ; Build Plate Adhesion Type : brim ; Brim Width : 4 mm ;----------------------------- Mesh Fixes -------------------------------- ; Union Overlapping Volumes : [True] ; Remove All Holes : [False] ;---------------------------- Special Modes ------------------------------ ; Print Sequence : all_at_once ; Spiralize Outer Contour : [False] ;---------------------------- Experimental ------------------------------- ; Tree Support : [False] ; Tree Support Branch Angle : 40 ° ; Tree Support Branch Distance : 1 mm ; Tree Support Branch Diameter : 2 mm ; Tree Support Branch Diameter Angle : 5 ° ; Enable Coasting : [False] ; Coasting Volume : 0.064 mm3 ; Coasting Speed : 90 mm/s ; Use Adaptive Layers : [False] ; Adaptive Layers Maximum Variation : 0.12 mm ; Adaptive Layers Variation Step Size : 0.04 mm ; Enable Bridge Settings : [True] ;==========================================================================