This is a Printables reupload: There are a lot of remixes and comments for troubleshooting on the original Thingiverse page: [https://www.thingiverse.com/thing:248009](https://www.thingiverse.com/thing:248009)

A clock that plots time. Designed with makeability in a fablab/makerspace/hackerspace in mind.

You need:

• Laser cutter or 3D printer
• 1 Arduino
• 3 servos
• 1 dry wipe pen
• M3 nuts, bolts, thread tap

Update to V1.01:

added calibration routine and documentation to arduino code

see the instruction tab above for building instructions

[http://wiki.fablab-nuernberg.de/w/Ding:Plotclock](http://wiki.fablab-nuernberg.de/w/Ding:Plotclock) (german) [http://www.youtube.com/watch?v=iOLFP90DneY](http://www.youtube.com/watch?v=iOLFP90DneY) [https://github.com/9a/plotclock](https://github.com/9a/plotclock) (old, not maintained!)

I'm not associated with any kits you are able to buy online

Instructions

Update 08/15: You might want to take a look at [http://www.thingiverse.com/thing:931498/#instructions](http://www.thingiverse.com/thing:931498/#instructions) for a more detailed documentation

Update 10/15: You should also check out [http://www.instructables.com/id/Plot-Clock-for-dummies/?ALLSTEPS](http://www.instructables.com/id/Plot-Clock-for-dummies/?ALLSTEPS) Thanks to Kjetil Egeland!

Materials I used:

• Arduino uno
• Tower Pro 9g servos (those cheap ones from ebay)
• WB SL DRYWIPE MARKER, bullet tip
• A small custom servo adapter, there are shields or servo-arduinos that also can be used. You can also just use jumper wires: 5V to red servo wire, GND to brown or black servo wire and the arduino servopins connected to the yellow or orange servo wire

Building instructions:

(for version 1.01!)

Lasercut plotclock_beta1.pdf from 3mm material or 3D print plotclock_SUP7.skp

• the black areas in the pdf on the servo arms should be used to engrave some material away, so the servohorns settle in
• use [http://www.thingiverse.com/thing:250204](http://www.thingiverse.com/thing:250204) for single STL files if you 3D print the clock (Thanks corben33!)

3D print swee.stl or reuse some other cylindrical part for the sweeper

Tap 2.5mm holes with M3 thread

Assemble arms with M3 screws, gently adjust the counternuts so that the joints under the screw heads just have enough play for smooth movement (see joint picture).

load Arduino sketch plotclock_V1, see code comments for further information

• [http://playground.arduino.cc/Code/time](http://playground.arduino.cc/Code/time) library is needed

Add some sort of cloth with double sided tape to sweeper

Attach servos to digital pin 2, 3 and 4, according to arduino sketch, test them without anything attached by plugging in the arduino (the photos show it being connected to 1, 2 and 3, which isn't optimal since 1 is also the TX pin, so during arduino startup the lifting servo jumps around)

Put everything together

• You may have to redrill the holes that are used for securing the servos, since some servo screws are a tight fit.

When attaching the servo arms, make sure they can turn enough to reach every point on the drawing surface by manually turning them

Power the arduino, it should start a calibration cycle where every second the position of both servos changes by rotating exactly 90 degrees (see last image in gallery)

Change the SERVOFAKTOR, SERVOLEFTNULL and SERVORIGHTNULL values until everything matches up (see code for more information)

Attach the pen and the sweeper holder only after testing everything else

This description is still a bit of a WIP, so comment if you have any questions!

Category: DIY