更新 update

20241106更新

由于有朋友反应顶盖处转轴部分支撑不方便拆除，所以修改了顶盖的模型文件，去掉了顶盖转轴处的支撑，增加了四角的圆形拓展避免翘边，请有需要的朋友下载这个文件：penbox_round_pikaqiu_19_2.9_6.5_p3_20241106.3mf

效果图如下：

描述 Description

设计灵感来自宝可梦里的皮卡丘，保留了可爱的眼睛、鼻子和红红的脸颊。所有分色配件都是分件设计可单独打印，整体拼装后很圆润结实，合缝也比较令人满意。组装这款笔盒需要准备3段打印耗材线和塑料用胶水就可以完成，不需要另外的五金件。盒内尺寸可以盛放铅笔，方便学生使用。希望大家能够喜欢这款笔盒。
The design is inspired by Pikachu from Pokémon, and retains the cute eyes, nose and red cheeks. All color-separated accessories are designed in parts and can be printed separately. After the whole is assembled, it is round and strong, and the joints are also quite satisfactory. To assemble this pencil case, you only need to prepare 3 sections of printing consumables and plastic glue, and no other hardware is required. The size of the box can hold pencils, which is convenient for students to use. I hope you will like this pencil case.

实物尺寸 Actual size

19cm*2.9cm*6.5cm

组装 Assembly

收纳盒组装时需要三段1.75mm耗材线，其中两段长度为1cm，用于顶端卡扣和上盖连接，一段长度为11cm，用于上盖和底部的连接。
Three sections of 1.75mm filament wire are required for assembling the storage box. Two of them are 1cm long and are used to connect the top buckle and the upper cover, and one section is 11cm long and is used to connect the upper cover and the bottom.

组装操作：Assembly Operation:

1.将两段1cm的1.75mm耗材丝插入卡口两端使两端齐平。

1. Insert two 1cm 1.75mm filaments into both ends of the bayonet so that both ends are flush.
2.将卡扣有孔洞的一端插入上盖缺口位置，用平口螺丝刀或其它工具将卡口内两段耗材丝分别推入上盖相应孔洞。

2. Insert the end of the buckle with the hole into the notch of the upper cover, and use a flat screwdriver or other tools to push the two filaments in the bayonet into the corresponding holes of the upper cover.

3.将11cm耗材丝放入上盖相应长条形孔洞，保持两端耗材丝不要突出。

3. Put the 11cm filament into the corresponding long hole of the upper cover, and keep the filaments at both ends from protruding.
4.将上盖相应位置安放到底部相应位置，用手将耗材丝推入底部两段孔洞。

4. Place the corresponding position of the upper cover on the corresponding position of the bottom, and push the filament into the two holes at the bottom by hand.

5.腮红部分一共有四块配件，请提前确定好位置后再使用胶水粘合。

5. There are four accessories for the blush part. Please determine the position in advance and then use glue to glue.
6.眼睛分黑色眼睛和白色高光，安装黑色眼睛时请对准下方卡口后进行粘合，白色高光部分使用胶水插入黑色眼睛预留位置。
6. The eyes are divided into black eyes and white highlights. When installing the black eyes, please align the lower bayonet and glue them. Use glue to insert the white highlight part into the reserved position of the black eyes.

打印建议 Printing suggestions

打印建议 Printing suggestions
1.打印时建议使用裙边设置以防止翘边。It is recommended to use the Skirt setting when printing to prevent warping.
2.为了强度建议使用0.16mm层高、3层墙厚、20%填充、螺旋纹填充。For strength, it is recommended to use 0.16mm layer height, 3 layers of wall thickness, 20% filling, spiral filling.

你的助力是对我最大的肯定，感谢你的支持。

Your support is the greatest affirmation to me, thank you for your support.