Update V2 06.10.2024 

Print Profile V2 and STLS have been updated !!!

• Updated Slider geometry, Updated Body geometry, 
• Magnet hole tolerances from +0,4mm to +0,6mm to allow better gravity feed and accept higer range of magnet tolleraces.
• Remooved extra gap and made the Sliders thickness speciffically to every magnet height
• Added Magnet Sizes: 3x1, 3x2, 4x1, 5x1, 6x1
• Changed Text to full Magnet size before: (4,5,6) now (4x1 4x2, 4x3, 5x1 5x2 5x3….)

If you wish to update to V2 you will need to reprint Body and Slider, the other parts (seat and Frame) remain the same. 

Hey guys,

I was not happy with any of the Magnet holders out there so i made one myself.

It is compatible with HSW as well as IKEA skadis, it is modular you can use one as a single unit or stack them up up to 8 units in total.

the trigger is suspended by a rubber band and will return to its resting position after pulling.

one pull produces one magnet at a time.

Magnet compatibility as follows:

• 3x1mm 3x2mm   (new)
• 4x1mm, 4x2mm  (new)
• 5x1mm, 5x2mm and (new)
• 6x1mm, 6x2mm and 6x3mm
• 7x2mm 7x3mm   (new)
• 8x2mm and 8x3mm
• 9x2mm 9x3mm   (new)
• 10x2mm and 10x3mm
• 11x2mm 11x3mm   (new)
• 12x2mm and 12x3mm
• stores up to 30 Magnets at 2mm thickness or 20Magnets at 3mm thickness. 

I also made another Version which holds 14mm to 20mm Magnets, the “BIG BOY” you can find on my main Page here:

[https://makerworld.com/en/models/655938#profileId-582939](https://makerworld.com/en/models/655938#profileId-582939)

have fun with either of theese and if you like it feel free to like comment, rate or even hit that boost:

Installation:

you will require one regular rubber band per unit, preferably around 30mm in diameter, others will work to, as you can tie a knot to shorten them.

1. Print all parts.

   1. you will need Dispenser(s), Slider(s), connector(s), and a frame according to the quanities of the amount you would like to stack.

    

2. slide the first dispensers onto the frame, and up so you have access to the slider section between.
3. Insert the rubber band through the back of the frame
4. Insert the slider into the dovetail from the front
5. place the rubber band over the trigger of the slider.
6. slide the dispenser into its final position while making sure not to pich the rubber band.
7. loop the rubber band around one of the tree tensioning points. again checking the band to prevent exessive drillup
8. repeat steps 2-7 untill all dispensers are on the frame
9. install your prefered connecter to the dovetail of the frame
10. slide the outer frame over the back of the unit to prefent the dispensers to come loose.

Load the Magnets and off you go.

(make sure to keep the polarity the same way around for every dispenser else the magnets might influence each other, especially on the 8-12mm sizes.)

Issue tracking:

due to its tight tolerances different printers might produce slightly different results especially on the dove tail of the slider. or the smaller 4mm hole. things like elephant foot or line skips can cause issues. here is what i found useful:

The slider:

the slider needs to run freely in the dove tail, i designed it with enough clearance however if you still have an issue you can give it a slight touch with some fine grid sandpaper at its tips.

4mm magnet hole:

again the clearance of all the holes is propotional so there should be enough room for the magnets to always fall to the bottom by gravity on its own. if its not then clean out the hole using a 4mm drill, twisting it inside the hole a couple times. that did the trick for me.

If you experiance any issues please let me know, i might have advise.

also this was a extended weekend design and surely can use some twaeking.

im currently optimizing the sliger.

so if you have any recommendations do not hesitate to let me know i will look into it.