Ir para conteúdo
3DFinder
Entrar

Você está no 3DFinder

Buscamos em Thingiverse, MakerWorld e Printables ao mesmo tempo para te dar o melhor de cada uma.

Buscar mais como este
Modelo 3D SUP 桨板推进器 6374 por asdhse no MakerWorld

Descrição

Please note that because the 6374/6384 motor is extremely powerful, the SUP fin pin may break and cause danger. I have uploaded the latest pin design, which requires an M3 * 45mm screw for reinforced fixation. Please print it with at least 6 walls.


適用於6374/6384推進器

M4*16mm 螺絲 4ea
M3*45mm screw 1ea 

一體打印

 

2026/06/20

增加B rev

免除馬達軸心支撐 增加插銷環洞

 

2026/06/22
update 6374 CCW/CW propeller

 

2026/6/24
Update SUP 6437 US FIN BOX
 

2026/7/11
Update Propeller Shroud
Simply clamp the motor and the fin together and tighten the screw.


Here are the components I bought from a local shop:

 Motor: 6374 Brushless Motor (waterproofed both the inner and outer rotors of the brushless motor using epoxy)

 ESC (Speed Controller): 60A ESC

 Receiver: 433MHz Receiver with a watch-style remote controller

 Wires: 12 AWG silicone wire

 Sealant: Epoxy resin

(Note: I'm not entirely sure if these exact brands/models are available in your area, but these are the general specs.)

 

The seal process for the 6374 brushless motor is divided into two main parts: the stator and the rotor.

  • For the rotor: I used a small brush to apply a very thin, even layer of epoxy resin. Keeping this layer thin is crucial to prevent throwing off the rotor's dynamic balance.
  • For the stator: I made a custom mold to fit around the entire coil and magnet assembly. First, I sealed the wire connections using 706 RTV silicone glue for flexible strain relief, and then I potted the entire component with epoxy.
     Just a couple of quick tips: make sure to seal or mask off the bearing area beforehand to prevent any epoxy from seeping in and ruining the bearings. Also, remember to thread screws into the screw holes when sealing the stator; this keeps the epoxy from leaking out through them


Parts list 
电机    [https://e.tb.cn/h.RDur2WZFdW2k40F?tk=CanXgm0UB3X](https://e.tb.cn/h.RDur2WZFdW2k40F?tk=CanXgm0UB3X)
               [https://www.aliexpress.com/item/1005008855710501.html?](https://www.aliexpress.com/item/1005008855710501.html?)
电调         [https://e.tb.cn/h.REBuwh9ECrF9CFi?tk=0KNtgm0UrU2](https://e.tb.cn/h.REBuwh9ECrF9CFi?tk=0KNtgm0UrU2)
                [https://www.aliexpress.com/item/1005010686461204.html?](https://www.aliexpress.com/item/1005010686461204.html?)
接收器 [https://e.tb.cn/h.REBvG5cSgK31zGy?tk=ld37gm0gMsl](https://e.tb.cn/h.REBvG5cSgK31zGy?tk=ld37gm0gMsl)

                [https://www.aliexpress.com/item/1005010151769598.html?](https://www.aliexpress.com/item/1005010151769598.html?)

MakerWorld

SUP 桨板推进器 6374

Publicado em 12 de jun de 2026

517
Curtidas
193
Downloads
1,121
Coleções
25
Impressões
Categoria RC
Tags
SUP 水下推进器 桨板 尾鳍 遙控 RC 6374 motor mount 6384
Licença Standard Digital File License - Community Use
Ver no MakerWorld (abre em nova aba)

Gostou deste modelo? Crie uma conta grátis para salvar seus favoritos e voltar a eles depois.

Criar conta