The Bralento Ritual Reed Diffuser – Slim Monolith is a minimalist, 3D-printable reed diffuser designed as an elegant and exclusive ritual object for modern interiors.

As part of the Bralento Ritual Series, it features the collection's signature vertical fluting — clean, architectural, and intentionally minimal. Unlike mass-market reed diffusers that are often short and bulky, this design introduces a tall, slim, and monolithic silhouette. The outer body and base align seamlessly, creating the look of a single, continuous sculptural object.

The Linear 7-Hole Layout

The completely flat top features a specialized 7-hole linear reed layout:

• 1 center hole (tighter fit to hold the middle reed perfectly straight)
• 3 left and 3 right holes (slightly wider to allow the reeds to angle outward)

This unique layout guides the reeds into a subtle, refined V-shaped fan, offering a highly decorative appearance that elevates any space compared to traditional chaotic openings.

Practical and Clean Design

The diffuser utilizes a removable inner container for the fragrance liquid. This independent core makes the assembly incredibly easy to clean, quick to refill, and highly practical for everyday use.

The model consists of:

• Outer Tower
• Base
• Removable Inner Container
• Optional Signature Label
• Separate B-Inlay

The Signature Label is optional, but honestly: print it. It gives the diffuser that extra premium detail — and yes, it looks exceptionally good.

Print Notes and Recommendations

General Support: OFF (The entire model is designed to print completely without supports).

Outer Tower and Base

• Layer height: 0.20 mm (good balance) or 0.16 mm (for an ultra-smooth premium surface)
• Wall loops: 3 recommended or 4 optional for a heavier, more solid feel
• Infill: 15–20%
• Material: PLA or PLA Matte (as shown in the product images)

Inner Container (The Core)

• Layer height: 0.20 mm or 0.16 mm
• Wall loops: 5 (Crucial for watertightness!)
• Infill: 20–30%
• Material: PETG recommended (More chemically resistant to oils than PLA)
• Note: Always test the printed container with water for 24 hours before filling it with fragrance oil.

Signature Label and B-Inlay

• Layer height: 0.12 mm (Extra Fine)
• Hardware: 0.4 mm nozzle works perfectly
• Orientation: Print flat on the build plate

Hardware and Capacity Specs

• Recommended Fill Amount: Up to approx. 90 ml of fragrance liquid (designed with an integrated safety margin).
• Recommended Reed Sticks: For the intended look, use 25 cm to 30 cm reed diffuser sticks with a diameter of approximately 3 mm.

Safety and Usage Note

This model serves as a decorative housing containing a removable fluid core.

Because different filaments, slicer settings, and specialized fragrance liquids vary greatly, you must test your inner container for watertightness before final use.

Do not overfill. Place the diffuser exclusively on stable, flat, and liquid-resistant surfaces. While PETG offers great chemical resistance, long-term compatibility with every proprietary fragrance oil recipe cannot be guaranteed. Keep away from children, pets, open flames, and active heat sources.

中文说明 / Chinese Description

Bralento Ritual Reed Diffuser – Slim Monolith 是一款简约、优雅且具有高级感的香薰藤条扩香器，适合现代家居、浴室、办公室、书架、边柜或桌面使用。

这款设计属于 Bralento Ritual Series，延续了安静、垂直、细腻的纹理语言。整体造型高挑、纤细、干净，不像传统扩香器那样矮胖或普通，而是更像一件现代室内设计摆件。

顶部采用完全平整的设计，并带有 7 个线性排列的藤条孔：

• 中间 1 个孔用于让中心藤条保持较直
• 左侧 3 个孔
• 右侧 3 个孔

这样可以让藤条形成一个柔和的 V 形扇面效果，使整体看起来更加优雅、平衡，也更具装饰性。

模型包含：

• Tower / 外壳
• Base / 底座
• removable Inner Container / 可取出的内胆容器
• 可选 Signature Label / 标识标签
• 独立 B-Inlay / B 字嵌件

Signature Label 是可选部件，但强烈建议打印并安装。它可以让整体外观更加完整，也更有高级设计感。

为了获得最佳视觉效果，建议使用：

• 25 cm 长的香薰藤条
• 直径约 3 mm 的藤条

建议最大填充量：

• 约 90 ml 香薰液
• 内胆容器已预留一定安全空间

可取出的内胆容器建议使用 PETG 打印，并在加入香薰液之前先用清水测试是否漏水。

打印建议

Tower / 外壳：
正常放置打印。
无需支撑。

Base / 底座：
正常放置打印。
无需支撑。

Inner Container / 内胆容器：
正常放置打印。
建议使用 PETG。
使用香薰液之前，请先用清水测试是否漏水。
无需支撑。

Signature Label / 标识标签：
平放打印。
无需支撑。

B-Inlay / B 字嵌件：
平放打印。
无需支撑。

推荐设置

Tower / Base：

• Layer height / 层高：0.20 mm，适合质量与打印时间的平衡
• 0.16 mm 可用于更精细的高级表面效果
• Wall loops / 壁数：建议 3 圈
• Infill / 填充：15–20 %
• Material / 材料：已测试 PLA / PLA Matte
• Support / 支撑：关闭

Inner Container / 内胆容器：

• Layer height / 层高：0.20 mm 或 0.16 mm
• Wall loops / 壁数：建议 5 圈
• Infill / 填充：15–20 %
• Material / 材料：建议 PETG
• 使用前请务必先用清水测试密封性

Signature Label / B-Inlay：

• 推荐 0.12 mm Extra Fine
• 0.4 mm 喷嘴可正常打印
• 平放打印
• 无需支撑

安全提示

本模型是用于香薰藤条扩香器的装饰外壳，并带有可取出的内胆容器。

使用前请先测试内胆容器是否漏水。不同材料、不同打印设置以及不同品牌的香薰液可能会产生不同效果。

请勿过量填充。请放置在稳定、平整且耐液体的表面上使用。

香薰液成分各不相同，可能会对不同材料产生影响。内胆容器建议使用 PETG 打印，但无法保证与所有香薰液长期完全兼容。

请远离儿童、宠物、明火和热源。