重要须知：

1. 强烈推荐使用 PETG 耗材：安全耐水泡。务必烘干耗材以防网孔拉丝！
2. 打印前，需要清洁打印板，或加胶水，或加外围裙边！务必三选一！

IMPORTANT NOTES:

1. PETG filament is highly recommended: It is safe for aquatic life and highly water-resistant. You must dry the filament to prevent stringing across the mesh holes!
2. Before printing, you must clean the build plate, apply glue, OR add an outer brim! You must do at least one of these three!

专为鱼缸设计，完美契合活泼上层鱼类的群游进食习惯。非常适合投喂极其细小的粉末级微粒鱼粮。近10厘米宽的超大底盘设计，让鱼群可以同时并排进食，不再拥挤抢食互相撕咬，您也不用再担心微小鱼粮漂浮满缸污染水质。

1.  0.25mm同心微滤网：完美兜住极小鱼粮颗粒，只透水不漏粮。
2. 秒沥干排气槽：侧壁设有排水泄压缝。将喂食器拎出水面时，哪怕底网被鱼粮糊死，水流也能瞬间从侧缝排出。
3. 气舱级霸道浮力：顶部宽大的圆环利用极低的内部填充率锁住海量空气，稳稳浮在水面。
4. 鱼类友好防刮伤：挑高加宽的进食门洞让鱼自由穿梭；顶部悬浮圈采用钻石 V 型底面，拆除树状支撑后接触面平滑，免打磨，绝不刮伤鱼鳞。

Designed specifically for freshwater aquariums, this feeder perfectly accommodates the schooling and surface-feeding habits of active top-dwelling fish. It is ideal for dispensing ultra-fine, powder-grade micro-pellets. The extra-large base (nearly 10 cm wide) allows a group of fish to feed side-by-side simultaneously, eliminating overcrowding, aggressive competition, and nipping. Plus, you no longer have to worry about micro-food drifting all over the tank and degrading your biological water quality.

1. 0.25mm Concentric Micro-Mesh: Perfectly catches extremely small food particles—allowing water to flow through while keeping the food contained.
2. Instant-Drain Vents: The side walls feature drainage and pressure-relief slits. When you lift the feeder out of the water, even if the bottom mesh is clogged with food paste, the water will instantly drain through these side vents.
3. Air-Cabin Level Buoyancy: The wide top floating ring utilizes a very low infill density to trap a massive volume of air, ensuring it floats steadily on the water surface.
4. Fish-Friendly & Scratch-Free: The raised and widened feeding portals allow fish to swim through freely. The top floating ring features a diamond V-shaped bottom; once the tree supports are removed, the contact surface remains completely smooth without needing any sanding, ensuring it will never scratch fish scales.

警告：清洁打印板/刷胶水/加裙边，请务必三选一！

底盘的微滤网由几十圈极细的同心塑料线组成，对首层粘附力要求极其高！打印前，请务清洁打印板或刷胶水！ 

备选方案，加裙边：如果打印板老化粘度下降，请在切片软件中开启 外围裙边 (Outer Brim)，宽度设为 5mm 左右。

WARNING: Clean the Build Plate / Apply Glue / Add a Brim — You MUST choose at least one! The bottom micro-mesh consists of dozens of extremely fine concentric plastic lines, which requires exceptionally high first-layer adhesion! Before printing, please make sure to clean the build plate or apply glue!

• Alternative Solution - Add a Brim: If your build plate is aging and losing its tackiness, please enable an Outer Brim in your slicer software (such as Bambu Studio), and set the brim width to around 5mm.