I am redoing a lot of my Pegboard in the garage with Multiboard ([https://multiboard.io](https://multiboard.io)).  I wanted something flexible so I could setup as many or few drivers or bits that I could use (keeping Torx separate from standard, etc.).   You can even, go with a single large hole to hold hammers, or other large handled tools.

Besides Multiboard, I also have code for OpenGRID, HSW and screw mounts, so I made that selectable.

So you can select a mount type from the following

• OpenGrid Lite ([https://makerworld.com/en/models/1175037-underware-for-opengrid?from=search#profileId-1195039](https://makerworld.com/en/models/1175037-underware-for-opengrid?from=search#profileId-1195039))
• OpenGrid Full
• Screws (#8 Flatheads).
• HSW Horizontal ([https://makerworld.com/en/models/22521-honeycomb-storage-wall?from=search#profileId-27457](https://makerworld.com/en/models/22521-honeycomb-storage-wall?from=search#profileId-27457))
• Multiboard SNAP ([https://www.multiboard.io](https://www.multiboard.io))
• Multiboard Screw (check the .3mp project for provided screws)
• Multiconnect - Multiboard (New!!!)
• Multiconnect - OpenGrid (New!!!)
• Pegboard Mount (need the thin Multiboard pegboard clicks [https://thangs.com/designer/Multiboard/3d-model/Pegboard%20Click%20-%20Lite%20Multipoint%20Rail%20%28Folded%29-1368649](https://thangs.com/designer/Multiboard/3d-model/Pegboard%20Click%20-%20Lite%20Multipoint%20Rail%20%28Folded%29-1368649))

Also a thanx to BlackJackDuck ([https://www.printables.com/model/1002471-multiboard-snap-backer-generator-parametric/files](https://www.printables.com/model/1002471-multiboard-snap-backer-generator-parametric/files)), that provided the OpenSCAD for the Multiboard Snaps.

If I missed anyone please let me know and I will update the text.

There are two configurations, either row by or as a wedge were each row forward is one less that the previous.

Parameters:

• Mount Type - Explained above
• Pattern - Standard (holes lined up in each row) or Triangle (Wedge)
• Num of Holes - how many holes across the back row (closest to back panel).
• Num of Rows -  1 to 5, note be careful here, to many rows and distance can place to much torque on SNAP.
• Left/Right to Center - Distance (mm) between left or right side to center of first hole.
• Front/Rear to Center - Distance (mm) between front or rear to center of holes in the row.
• Center to Center - Distance (mm) between centers of the holes in the row.
• Block Height - How tall (mm) the row bock will be, each row is stepped based this.  Example: 60mm/3rows, back row 60, row 2 - 40mm,  row 3 - 20mm.
• Hole Dia - Hole Diameter (mm), not there is no built in slot, you will want to add some variance in.
• Hole Chamfer - Diagonal cut (mm) around the hole, to better sit some items, like precision screw drivers.
• Hole Depth - How deep is the hole (mm), 0 mean s it goes all the way through.  Note, depending on the block height, the front holes may not have a bottom.  Take that into account when setting Block Height.
• Back Plate Thickness - How thick (mm) to make the back plate for additional strength.  This does not include the SNAPs.
• Edge Chamfer - Radius (mm) to round all outside edges.  Note: if this is to large compared to Back Plate, it may generate and error.

I hope you can use it.  

One future enhancement is being able to notch the front of the hole,  to be abled to lift the tool out without having a higher clearance.  It will only be for single rows models.

02/24/26 - Added additional mounts to the mix, not have Multiconnect, so you don't have to use snaps, also can now do standard Pegboards.