P2S First Layer Adhesion Test ⧸ Bed Cleaning

Maximize your P2S first layer success with the largest coverage adhesion tester on MakerWorld, lifting cleanly with its comfort pull tab for quick, frustration-free checks.

This model brings the proven A1 adhesion test concept to the new P2S. It is designed to cover a wide print area so you can quickly verify Z-offset, nozzle flow and surface adhesion.

The continuous line pattern makes it easy to detect if the first layer is too high or too low. Once the print is complete, the plate lifts off cleanly using the integrated comfort pull tab, leaving the bed ready for your next job.

Use this test after nozzle swaps, filament changes, or bed cleaning to confirm consistent adhesion and a clean surface.

Part #01 in my P2Series Design Journey.

Highlights:

Maximum printable area for P2S printers on MakerWorld
Comfort grip tab for quick and easy removal
Parametric customization via the MakerWorld Customizer
Optimized for bed leveling and adhesion diagnostics

Customization Tips:

Fine-tune the gap from purge strip and plate edges directly in the Customize section to match your needs perfectly.

Helpful Advice:

2 layers highlight surface inconsistencies without excessive adhesion
1 layer shows trouble spots faster but sticks tighter - remove carefully!
Clean the plate thoroughly using warm water and dish detergent (not hand soap)
Always run a calibration under Device → Calibration before testing for best results

More Build Plate Cleaners & Testers

Using a different Bambu Lab printer? No worries - I’ve designed build plate cleaners and testers tailored to other models as well.
Same idea, just perfectly adapted to fit each build plate. Check them out to keep your prints sticking flawlessly and your bed spotless, no matter which machine you’re using.

**Bambu Lab H2D Build Plate Cleaner and Tester**
Designed for the H2D’s build plate—easy to print, super effective, and perfect for quick alignment checks.

[https://makerworld.com/models/1271342-bambu-lab-h2d-build-plate-cleaner-and-tester](https://makerworld.com/models/1271342-bambu-lab-h2d-build-plate-cleaner-and-tester)

**Bambu Lab H2S Build Plate Cleaner and Tester**
Designed for the H2S build plate—single nozzle, full print

[https://makerworld.com/models/1750513-h2s-first-layer-adhesion-test-bed-cleaning](https://makerworld.com/models/1750513-h2s-first-layer-adhesion-test-bed-cleaning)

**Bambu Lab X1C / X1E Full Size Bed Cleaner and Tester**
Covers the full bed of the X1 series—ensures optimal adhesion across the entire surface.

[https://makerworld.com/models/1046216-bambu-lab-x1c-x1e-full-size-bed-cleaner-and-tester](https://makerworld.com/models/1046216-bambu-lab-x1c-x1e-full-size-bed-cleaner-and-tester)

**Bambu Lab P1S / P1P Full Size Bed Cleaner and Tester**
The classic cleaner for the P1 series—great for maintenance and adhesion troubleshooting.

[https://makerworld.com/models/1007968-bambu-lab-p1s-p1p-full-size-bed-cleaner-and-tester](https://makerworld.com/models/1007968-bambu-lab-p1s-p1p-full-size-bed-cleaner-and-tester)

**Bambu Lab A1 Full Build Plate Cleaner and Tester**
Made to match the A1’s full print area—parametric and practical.

[https://makerworld.com/models/1007393-bambu-lab-a1-full-build-plate-cleaner-and-tester](https://makerworld.com/models/1007393-bambu-lab-a1-full-build-plate-cleaner-and-tester)

**Bambu Lab A1 mini Build Plate Cleaner and Tester**
A must-have utility for the A1 mini—compact, effective, and easy to print.

[https://makerworld.com/models/1007564-bambu-lab-a1-mini-build-plate-cleaner-and-tester](https://makerworld.com/models/1007564-bambu-lab-a1-mini-build-plate-cleaner-and-tester)

Descrição

Highlights:

Customization Tips:

More Build Plate Cleaners & Testers